Nissan-Datsun 370Z Technical 12-053 Date: 120622
Engine Controls - MIL ON/DTC P0106 Stored In Memory
Classification: EC12-013
Reference: NTB12-053
Date: June 22, 2012
2010 - 2012 370Z; MIL "ON" WITH DTC P0106 STORED
APPLIED VEHICLE: All 2010-2012 370Z Coupe and Roadster (Z34/HZ34)
IF YOU CONFIRM:
An APPLIED VEHICLE has the MIL 'ON' with DTC P0106 (Manifold Absolute Pressure (MAP) circuit range/performance) stored in the ECM.
ACTION:
1. Refer to step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on.
2. If this bulletin applies, reprogram the ECM with CONSULT III plus ONLY.
Page 79
CLAIMS INFORMATION
IMPORTANT:
The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE
PROCEDURE as it contains information that is essential to successfully completing this repair.
Service Procedure
NOTE:
^ Most instructions for reprogramming with CONSULT-III plus (C-III plus) are displayed on the CONSULT PC screen.
^ If you are not familiar with the reprogramming procedure, refer to "CONSULT- III plus (C-III plus) ECM Reprogramming" general
procedure.
^ Take the vehicle for a 10 minute drive in order to meet the following Idle Air Volume Learn (IAVL) conditions:
> Engine coolant temperature: 70-100°C (158-212°F)
> Battery voltage: More than 12.9V (At idle)
> Transmission: Warmed up
^ After reprogramming is complete, you will be required to perform Throttle Valve Closed Position, Idle Air Volume Learn, Accelerator
Closed Position, and DTC erase.
Page 80
CAUTION
Page 81
Page 82
Page 83
Page 84
Page 85
SERVICE PROCEDURE
ECM recovery:
Do not disconnect plus VI or shut down CONSULT III plus if reprogramming does not complete.
Page 86
If reprogramming does not complete and the "!?" icon displays as shown in Figure 5 shown above and information shown above.
If reprogramming does not complete and the "X" icon displays as shown in Figure 6 shown above and information shown above.
Engine Controls - MIL ON/DTC P0106 Stored In Memory
Classification: EC12-013
Reference: NTB12-053
Date: June 22, 2012
2010 - 2012 370Z; MIL "ON" WITH DTC P0106 STORED
APPLIED VEHICLE: All 2010-2012 370Z Coupe and Roadster (Z34/HZ34)
IF YOU CONFIRM:
An APPLIED VEHICLE has the MIL 'ON' with DTC P0106 (Manifold Absolute Pressure (MAP) circuit range/performance) stored in the ECM.
ACTION:
1. Refer to step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on.
2. If this bulletin applies, reprogram the ECM with CONSULT III plus ONLY.
Page 79
CLAIMS INFORMATION
IMPORTANT:
The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE
PROCEDURE as it contains information that is essential to successfully completing this repair.
Service Procedure
NOTE:
^ Most instructions for reprogramming with CONSULT-III plus (C-III plus) are displayed on the CONSULT PC screen.
^ If you are not familiar with the reprogramming procedure, refer to "CONSULT- III plus (C-III plus) ECM Reprogramming" general
procedure.
^ Take the vehicle for a 10 minute drive in order to meet the following Idle Air Volume Learn (IAVL) conditions:
> Engine coolant temperature: 70-100°C (158-212°F)
> Battery voltage: More than 12.9V (At idle)
> Transmission: Warmed up
^ After reprogramming is complete, you will be required to perform Throttle Valve Closed Position, Idle Air Volume Learn, Accelerator
Closed Position, and DTC erase.
Page 80
CAUTION
Page 81
Page 82
Page 83
Page 84
Page 85
SERVICE PROCEDURE
ECM recovery:
Do not disconnect plus VI or shut down CONSULT III plus if reprogramming does not complete.
Page 86
If reprogramming does not complete and the "!?" icon displays as shown in Figure 5 shown above and information shown above.
If reprogramming does not complete and the "X" icon displays as shown in Figure 6 shown above and information shown above.
