Nissan-Datsun 370Z Technical 10-002 Date: 100112
Engine - Drive Belt Noise Diagnosis
Classification: EM09-013
Reference: NTB10-002
Date: January 12, 2010
DRIVE BELT SYSTEM NOISE DIAGNOSIS
APPLIED VEHICLES All Nissan
IF YOU CONFIRM
There is noise coming from the drive belt(s), or drive belt pulley(s),
ACTION
Use the flow chart in this bulletin to help diagnose and identify the source / cause of the noise.
CLAIMS INFORMATION
Refer to the current Nissan Warranty Flat Rate Manual and use the indicated claims coding for any repairs performed.
Page 227
Page 228
DRIVE BELT / PULLEY NOISE DIAGNOSIS FLOW CHART
Page 229
Auto tensioner Inspection (if equipped)
1. With the engine running at idle and the AC turned ON, observe the pulley angular (side to side) movement (see Example 1):
^ See above table for maximum movement specification.
^ Visual comparison of movement with a known good vehicle is recommended.
2. With the engine running at idle and the AC turned ON, observe the pulley axial/lateral (back and forth) movement (see Example 2):
^ Maximum movement specification is 1 mm.
Page 230
^ Visual comparison of movement with a known good vehicle is recommended.
Idler Pulley / Manual Tensioner Inspection (if equipped)
No more than 1 mm of pulley rock should be visible.
Alternator One-way Clutch Pulley Inspection
CAUTION:
Be careful not to damage the rotor.
NOTE:
The following steps can be done while the alternator is installed on the vehicle if the drive belt is removed and the alternator electrical connectors are
disconnected.
1. Secure the rotor using a medium size screwdriver and a rolled shop towel.
2. Turn the pulley clockwise when viewed from the front.
^ Pulley should be locked.
^ If it rotates in both directions, replace the alternator.
3. Turn the pulley counterclockwise when viewed from the front.
^ Pulley should turn with some dragging
^ If it locks or has unusual resistance, replace the alternator.
Engine - Drive Belt Noise Diagnosis
Classification: EM09-013
Reference: NTB10-002
Date: January 12, 2010
DRIVE BELT SYSTEM NOISE DIAGNOSIS
APPLIED VEHICLES All Nissan
IF YOU CONFIRM
There is noise coming from the drive belt(s), or drive belt pulley(s),
ACTION
Use the flow chart in this bulletin to help diagnose and identify the source / cause of the noise.
CLAIMS INFORMATION
Refer to the current Nissan Warranty Flat Rate Manual and use the indicated claims coding for any repairs performed.
Page 227
Page 228
DRIVE BELT / PULLEY NOISE DIAGNOSIS FLOW CHART
Page 229
Auto tensioner Inspection (if equipped)
1. With the engine running at idle and the AC turned ON, observe the pulley angular (side to side) movement (see Example 1):
^ See above table for maximum movement specification.
^ Visual comparison of movement with a known good vehicle is recommended.
2. With the engine running at idle and the AC turned ON, observe the pulley axial/lateral (back and forth) movement (see Example 2):
^ Maximum movement specification is 1 mm.
Page 230
^ Visual comparison of movement with a known good vehicle is recommended.
Idler Pulley / Manual Tensioner Inspection (if equipped)
No more than 1 mm of pulley rock should be visible.
Alternator One-way Clutch Pulley Inspection
CAUTION:
Be careful not to damage the rotor.
NOTE:
The following steps can be done while the alternator is installed on the vehicle if the drive belt is removed and the alternator electrical connectors are
disconnected.
1. Secure the rotor using a medium size screwdriver and a rolled shop towel.
2. Turn the pulley clockwise when viewed from the front.
^ Pulley should be locked.
^ If it rotates in both directions, replace the alternator.
3. Turn the pulley counterclockwise when viewed from the front.
^ Pulley should turn with some dragging
^ If it locks or has unusual resistance, replace the alternator.
