Skip to main content

Nissan-Datsun 370Z Technical 09-016A Date: 100909 Body - Can't Raise Windows With Doors Open

Nissan-Datsun 370Z Technical  09-016A Date: 100909
Body - Can't Raise Windows With Doors Open
Classification: EL09-007A
Reference: NTB09-016A
Date: September 9, 2010
370Z; DOOR WINDOW OPERATION
This bulletin has been amended. The Applied Vehicles section has been revised. No other changes have been made. Please discard all previous
copies.
APPLIED VEHICLES:
2009-2010 370Z Coupe (Z34)
2010 370Z Roadster (HZ34)
  Page 272
IF YOU CONFIRM
Upon opening either the driver's or passenger's door, the door windows cannot be raised, with the door open.
AND
The battery state-of-charge is low,
OR
The battery, for whatever reason, had been temporarily disconnected.
ACTIONS
DO NOT replace the power window motor or power window switch.
If the battery state-of-charge is low, service the battery as indicated by use of the Midtronics GR-8 Battery and Diagnostic Station using standard
Warranty procedures.
Re-initialize the windows using the Service Procedure.
NOTE:
This procedure can also be found in Section 2 of the 370Z Owner's Manual.
^ The power window has an automatic adjusting function.
^ When the door is being opened, the window is automatically lowered slightly to avoid contact between the window and the side roof panel.
^ When the door is closed, the window is automatically raised slightly.
SERVICE PROCEDURE
1. Push the ignition switch to the ON position.
2. Close the door.
3. Open the window more than halfway by operating the power window switch.
4. Pull the power window switch and hold it to close the window, and then hold the switch more than 3 seconds after the window is closed
completely.
5. Release the power window switch. Operate the window by the automatic function to confirm the initialization is complete.
6. Performs steps 2 through 5 above for the other window.

Comments

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconn...

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on. ...

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021 Steering/Suspension - Wheel Bearing Collision Damage Classification: FA10-006 Reference: NTB10-126 Date: October 21, 2010 WHEEL BEARING COLLISION DAMAGE APPLIED VEHICLES: All Nissan SERVICE INFORMATION Impacts to wheel bearings (such as a collision or other suspension damage) may create slight indents in the bearing surfaces. These indents may not 2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 446 be visible but can cause bearing noise. NOTE: Hub/bearing replacement due to impact (collision or other suspension damage) is not a warrantable repair If a vehicle has visible wheel or suspension damage due to impact (collision or other suspension damage), it is recommended that the wheel bearing assembly be inspected as follows: 1. Remove the hub/bearing assembly from the vehicle. 2. Hold the hub/bearing assembly with both hands. 3. Rotate the hub/bearing assembly in both directions (clockwise and counterclockwise). 4. If any gr...