Skip to main content

ALPHA RONIN GTR

Performance Specifications
  • Quarter Mile:  9.8@145mph
  • 0-60mph:    2.3 Seconds
  • 0-100mph:    5.1 Seconds
  • 60-130mph:  5.46 Seconds
Engine:
  • Alpha Ronin 4.1L Stroker Engine
  • Alpha Ronin Camshafts and Valve Springs
  • Alpha Cooling Package
Turbo/Exhaust:
  • Alpha Ronin Turbo System
  • Alpha 90mm Downpipes
  • Tial BOV’s
  • Alpha Ronin 94mm Stainless Steel Exhaust System
  • Titanium 102mm Exhaust System
Fuel:
  • Alpha Complete Fuel System Upgrade
Transmission:
  • Alpha Ronin Spec Transmission by Shepherd Racing
  • HD Axle & Hub Upgrade
Intake/Intercooler:
  • Alpha Intake Manifold Upgrade
  • Alpha Race FMIC
  • Alpha Induction Kit and Intercooler Piping
Exterior:
  • Ronin Carbon Fiber Trim Package Including Roof
Engine Management/Electronics:
  • Syvecs Stand-alone Engine Management System
  • Alpha Ronin GT-R Calibration File (93 octane)
Suspension/Rims/Tires:
  • Forgeline Ronin 20″ Wheels & Michelin Pilot Super Sport Tires 
  • Alpha Track Package w/ Litchfield Suspension Upgrade
Full Ronin Package details can be seen here.

Comments

Post a Comment

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconn...
Post a Comment
Read more

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on. ...
Post a Comment
Read more

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021 Steering/Suspension - Wheel Bearing Collision Damage Classification: FA10-006 Reference: NTB10-126 Date: October 21, 2010 WHEEL BEARING COLLISION DAMAGE APPLIED VEHICLES: All Nissan SERVICE INFORMATION Impacts to wheel bearings (such as a collision or other suspension damage) may create slight indents in the bearing surfaces. These indents may not 2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 446 be visible but can cause bearing noise. NOTE: Hub/bearing replacement due to impact (collision or other suspension damage) is not a warrantable repair If a vehicle has visible wheel or suspension damage due to impact (collision or other suspension damage), it is recommended that the wheel bearing assembly be inspected as follows: 1. Remove the hub/bearing assembly from the vehicle. 2. Hold the hub/bearing assembly with both hands. 3. Rotate the hub/bearing assembly in both directions (clockwise and counterclockwise). 4. If any gr...
Post a Comment
Read more