Skip to main content

2014 Nissan-Datsun Altima Diagrams. DTC # 00-042B Date: 110215

2014 Nissan-Datsun Altima Diagrams. DTC # 00-042B Date: 110215



Interior/Restraints - Seat Trim Material Information



Classification: RS00-003B



Reference: NTB00-042B



Date: February 15, 2011



RECOMMENDATION AGAINST MAKING CHANGES TO FRONT SEAT ASSEMBLY TRIM MATERIALS



This bulletin has been amended. The Applied Vehicles and Service Information have been updated. Discard all previous copies.



APPLIED VEHICLES: ALL NISSAN VEHICLES



SERVICE INFORMATION



Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact



Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death.



Nissan STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition. This specifically



applies to replacing the seat trim with non-factory materials; adding leather/cloth seat covers seat pads or seat storage pouches etc. around or over



2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 231



the seat back and the passenger seat cushion.



^ Damage or failure due to changes or modifications to the front seat assembly are not covered under the warranty.



^ Damage or failure due to changes or modifications to the front seat assembly are not subject to indemnification under the Nissan Dealer Sales and



Service Agreement.



^ Dealers may be obligated under their Nissan Dealer Sales and Service Agreement to indemnify Nissan for any damages, injuries, or deaths caused



by modification of the front seat assemblies.



^ NMAC will not provide retail advance for any changes to the front seat trim materials from factory equipped condition.



^ Vehicles with any changes to the front seat trim materials from factory equipped condition may not be eligible for the Signature PURCHASE



Plan.



SEE Section 1 of the applicable Owner's Manual for important Warnings and other information about Front Seat-Mounted Side-Impact



Supplemental Air Bags and Passenger Occupant Classification Sensor.

Labels:

Comments

Post a Comment

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconn...
Post a Comment
Read more

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on. ...
Post a Comment
Read more

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021 Steering/Suspension - Wheel Bearing Collision Damage Classification: FA10-006 Reference: NTB10-126 Date: October 21, 2010 WHEEL BEARING COLLISION DAMAGE APPLIED VEHICLES: All Nissan SERVICE INFORMATION Impacts to wheel bearings (such as a collision or other suspension damage) may create slight indents in the bearing surfaces. These indents may not 2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 446 be visible but can cause bearing noise. NOTE: Hub/bearing replacement due to impact (collision or other suspension damage) is not a warrantable repair If a vehicle has visible wheel or suspension damage due to impact (collision or other suspension damage), it is recommended that the wheel bearing assembly be inspected as follows: 1. Remove the hub/bearing assembly from the vehicle. 2. Hold the hub/bearing assembly with both hands. 3. Rotate the hub/bearing assembly in both directions (clockwise and counterclockwise). 4. If any gr...
Post a Comment
Read more