Skip to main content

Ford issues recalls for F-Series truck windshields, Super Duty payload labels


Ford has issued two safety recalls involving its trucks.


The first recall involves a select number of 2021-21 F-Series trucks for an issue with windshields that were inadequately bonded to the vehicle.


The recall affects a specific number of trucks: 79,017 of them in the U.S., 6,986 in Canada and 1,347 in Mexico.


The affected trucks are:

2021 Ford F-150 pickups built in Dearborn, Mich., between Oct. 27, 2020, and Feb. 3, 2021. 2020-21 Ford Super Duty trucks built in Kentucky between Oct. 13, 2020, and Jan. 23, 2021.

Ford says it's not aware of any accidents or injuries involving this windshield issue.


If you're an owned of an affected truck, notifications will begin April 6. Dealers will remove and reinstall the windshield.?


Owner notifications will begin the week of April 6. Dealers will remove and reinstall the windshield using standard service procedures. The Ford reference number for this recall is 21C06.

In the second recall:

A select number of 2020 Ford Super Duty trucks with 6.7-liter engines "display overstated payload capacity values on the tire and loading information label, overstated accessory reserve capacity values on the safety certification label, and overstated weight values on the truck camper loading documentation."?


Meaning, if you were to load the trucks to those values, you could exceed the gross vehicle weight rating or gross axle weight rating. You'd be overloaded past the capacity of the tires or suspension, which could lead to a crash.


This recall affects?9,979 examples of the 2020 Ford F-Series Super Duty in the U.S. and 1,750 in Canada, built in Kentucky between May 13, 2019, and Sept. 19, 2020.


Ford is not aware of any accidents or injuries related to this issue, either. Notifications will begin the week of March 22. Reference number for this recall is 21S06.


?


?

Ford

Comments

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconnect

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on.

C1142 C1142 PRESS SENSOR

**************************** **************************** C1142 C1142 PRESS SENSOR Description The front and rear pressure sensors convert the brake fluid pressure to an electric signal and transmit it to the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1142. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. FRONT PRESSURE SENSOR 1.CONNECTOR INSPECTION 1. Turn the ignition switch OFF. 2. Disconnect the front pressure sensor connector and ABS actuator and electric unit (control unit) connector and inspect the terminals for deformation, disconnection, looseness, or damage. Is the inspection result normal? YE