Skip to main content

C1140 C1140 ACTUATOR RLY

****************************
****************************


C1140
C1140 ACTUATOR RLY
Description
Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit).
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAGNOSIS RESULTS
Check the self-diagnosis results.
Is above displayed on the self-diagnosis display?
YES - Proceed to diagnosis procedure. See: C1140.
NO - Inspection End
Diagnosis Procedure
Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical
Diagrams.
1.CONNECTOR INSPECTION
1. Turn ignition switch OFF.
2. Disconnect ABS actuator and electric unit (control unit) connector.
3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal.
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49
4. Reconnect connectors and then perform the self-diagnosis. See: Brakes and Traction Control/Antilock Brakes / Traction Control
Systems/Testing and Inspection/Scan Tool Testing and Procedures.
Is any item indicated on the self-diagnosis display?
YES - GO TO 2
NO - Poor connection of connector terminal. Repair or replace connector.
2.CHECK SOLENOID, VDC SWITCH-OVER VALVE AND ACTUATOR RELAY POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect ABS actuator and electric unit (control unit) connector.
3. Check voltage between ABS actuator and electric unit (control unit) connector E125 terminal 32 and ground.
Is the inspection result normal?
YES - GO TO 3
NO - Repair or replace malfunctioning components.
3.CHECK SOLENOID, VDC SWITCH-OVER VALVE AND ACTUATOR RELAY GROUND CIRCUIT
Check continuity between ABS actuator and electric unit (control unit) connector E125 terminals 16, 47 and ground.
Is the inspection result normal?
YES - Replace ABS actuator and electric unit (control unit). See: Brakes and Traction Control/Antilock Brakes / Traction Control
Systems/Hydraulic Control Assembly - Antilock Brakes/Service and Repair.
NO - Repair or replace malfunctioning components.
Component Inspection
1.CHECK ACTIVE TEST
1. On "ACTIVE TEST", select "ABS MOTOR".
2. Touch "On" and "Off" on screen. Make sure motor relay and actuator relay operates as shown in table below.
Is the inspection result normal?
YES - Inspection End
NO - Go to diagnosis procedure. See: C1140.
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 50
Special Repair Requirement
1.ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
Always perform neutral position adjustment for the steering angle sensor when replacing the ABS actuator and electric unit (control unit). See:
Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Steering Angle Sensor/Testing and Inspection/Description.
- GO TO 2
2.CALIBRATION OF DECEL G SENSOR
Always perform calibration of decel G sensor when replacing the ABS actuator and electric unit (control unit). See: Brakes and Traction
Control/Antilock Brakes / Traction Control Systems/Yaw Rate Sensor/Testing and Inspection/Description.
- END

Labels

Labels:
Location: 1321 State Rd S-14-636, Summerton, SC 29148, USA

Comments

Post a Comment

Popular posts from this blog

C1156 C1156 ST ANG SEN COM CIR

**************************** **************************** C1156 C1156 ST ANG SEN COM CIR Description The steering angle sensor is connected to the ABS actuator and electric unit (control unit) in addition to CAN lines. CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle multiplex communication line with high data communication speed and excellent error detection ability. Many electronic control units are equipped onto a vehicle, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with 2 communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only. DTC Logic DTC DETECTION LOGIC Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 62 DTC CONFIRMATION PROCED...
Post a Comment
Read more

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021 Steering/Suspension - Wheel Bearing Collision Damage Classification: FA10-006 Reference: NTB10-126 Date: October 21, 2010 WHEEL BEARING COLLISION DAMAGE APPLIED VEHICLES: All Nissan SERVICE INFORMATION Impacts to wheel bearings (such as a collision or other suspension damage) may create slight indents in the bearing surfaces. These indents may not 2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 446 be visible but can cause bearing noise. NOTE: Hub/bearing replacement due to impact (collision or other suspension damage) is not a warrantable repair If a vehicle has visible wheel or suspension damage due to impact (collision or other suspension damage), it is recommended that the wheel bearing assembly be inspected as follows: 1. Remove the hub/bearing assembly from the vehicle. 2. Hold the hub/bearing assembly with both hands. 3. Rotate the hub/bearing assembly in both directions (clockwise and counterclockwise). 4. If any gr...
Post a Comment
Read more