Nissan-Datsun 370Z Technical 09-136 Date: 091201 Engine Controls - ECM VIN Registration Procedure Classification: EC09-028

 Nissan-Datsun 370Z Technical  09-136 Date: 091201
Engine Controls - ECM VIN Registration Procedure
Classification: EC09-028
Reference: NTB09-136
Date: December 1, 2009
2005 AND LATER; ECM VIN REGISTRATION
APPLIED VEHICLES: All Nissan 2005 and later
SERVICE INFORMATION
The Applied Vehicles must have the correct Vehicle Identification Number (VIN) registered in the Engine Control Module (ECM). The VIN
registration process must be performed under the following conditions.
^ When installing a new ECM
^ If, during vehicle service, the VIN registration inside the ECM is found to be missing or incorrect.
When needed, use the Service Procedure in this bulletin to perform ECM VIN registration.
CLAIMS INFORMATION
Refer to the current Nissan Warranty Flat Rate Manual and use the appropriate claims coding for any repairs being performed.
SERVICE PROCEDURE
1. Connect C-III to the vehicle and perform the initial selections:
NOTE:
If C-III is already connected, go to Step 2.
a. Start C-III and Wait for the "Detecting VI/MI in progress" message to clear.
b. Select the detected VI from the list.
c. Wait for the "Checking the firmware version" message to clear.
d. Select Model and Year.
e. Confirm the correct model and year were selected.
f. Select Repair.
  Page 233
2. Select Direct Diagnostic Mode icon
3. Select System Diagnosis
  Page 234
4. Select Engine
5. Select OK
6. Select Work Support
  Page 235
7. Select VIN Registration
8. Select Next
9. Make sure the ignition is ON with engine OFF.
10. Select Start
  Page 236
11. Enter the VIN into C-III two times (see Figure 7).
^ Touch the C-III screen in the "VIN box" before typing.
^ Make sure to use all CAPITAL LETTERS.
^ Use the VIN from the vehicle you are working on.
12. Select Start
13. Turn the ignition OFF, and wait 10 seconds.
14. After waiting 10 seconds, turn the ignition ON.
  Page 237
15. Select OK
VIN registration is complete

Nissan-Datsun 370Z Technical 09-024B Date: 091215 Wheels - Accessory Wheel Lock Availability Classification: WT09-001B

 Nissan-Datsun 370Z Technical  09-024B Date: 091215
Wheels - Accessory Wheel Lock Availability
Classification: WT09-001B
  Page 231
Reference: NTB09-024B
Date: December 15, 2009
2009 - 2010 370Z / 2009 350Z ACCESSORY WHEEL LOCKS
This bulletin has been amended. The Applied Vehicles have been updated. Please discard previous versions of this bulletin.
APPLIED VEHICLES:
2009 370Z (Z34) Coupe
2010 370Z (Z34) Coupe and Roadster
2009 350Z (Z33) Roadster
SERVICE INFORMATION
The accessory Wheel Lock Nuts for 370Z are different than those for 350Z.
When installing Wheel Lock Nuts, make sure to use the correct Part Number as listed below.
NOTE:
See below for additional information.
CLAIMS INFORMATION
Accessory wheel lock nuts and/or vehicle wheels that are damaged due to installation of the wrong nuts will not be considered a manufacturer defect
and will not be covered under warranty.
Accessory Wheel Lock Installation / Removal Guidelines
^ Always use hand tools when installing or removing accessory wheel lock nuts.
^ WARNING:
Do not use power tools to install or remove accessory wheel lock nuts.
^ For ease of removal, the wheel lock nut should always be the first lug nut removed.
^ If needed, clean threads on lug studs with a wire brush.
^ The wheel lock nut should always be the last lug nut tightened.
^ Always use the special key supplied in the wheel lock set to install and remove the wheel locks.
  Page 232
^ Always tighten the wheel lock nuts - using a hand torque wrench - to the torque specification in the Service Manual.

Nissan-Datsun 370Z Technical 10-002 Date: 100112 Engine - Drive Belt Noise Diagnosis Classification: EM09-013 Reference: NTB10-002

 Nissan-Datsun 370Z Technical  10-002 Date: 100112
Engine - Drive Belt Noise Diagnosis
Classification: EM09-013
Reference: NTB10-002
Date: January 12, 2010
DRIVE BELT SYSTEM NOISE DIAGNOSIS
APPLIED VEHICLES All Nissan
IF YOU CONFIRM
There is noise coming from the drive belt(s), or drive belt pulley(s),
ACTION
Use the flow chart in this bulletin to help diagnose and identify the source / cause of the noise.
CLAIMS INFORMATION
Refer to the current Nissan Warranty Flat Rate Manual and use the indicated claims coding for any repairs performed.
  Page 227
  Page 228
DRIVE BELT / PULLEY NOISE DIAGNOSIS FLOW CHART
  Page 229
Auto tensioner Inspection (if equipped)
1. With the engine running at idle and the AC turned ON, observe the pulley angular (side to side) movement (see Example 1):
^ See above table for maximum movement specification.
^ Visual comparison of movement with a known good vehicle is recommended.
2. With the engine running at idle and the AC turned ON, observe the pulley axial/lateral (back and forth) movement (see Example 2):
^ Maximum movement specification is 1 mm.
  Page 230
^ Visual comparison of movement with a known good vehicle is recommended.
Idler Pulley / Manual Tensioner Inspection (if equipped)
No more than 1 mm of pulley rock should be visible.
Alternator One-way Clutch Pulley Inspection
CAUTION:
Be careful not to damage the rotor.
NOTE:
The following steps can be done while the alternator is installed on the vehicle if the drive belt is removed and the alternator electrical connectors are
disconnected.
1. Secure the rotor using a medium size screwdriver and a rolled shop towel.
2. Turn the pulley clockwise when viewed from the front.
^ Pulley should be locked.
^ If it rotates in both directions, replace the alternator.
3. Turn the pulley counterclockwise when viewed from the front.
^ Pulley should turn with some dragging
^ If it locks or has unusual resistance, replace the alternator.

Nissan-Datsun 370Z Technical 09-141 Date: 091208 Engine - Reman Engine Start Up Lubrication Information Classification: EM09-010

 Nissan-Datsun 370Z Technical  09-141 Date: 091208
Engine - Reman Engine Start Up Lubrication Information
Classification: EM09-010
Reference: NTB09-141
Date: December 8, 2009
REMANUFACTURED ENGINE LUBRICATION UPON INITIAL START UP
APPLIED VEHICLE: All Nissan vehicles having a remanufactured engine installed
SERVICE INFORMATION
  Page 226
During remanufactured engine storage, upper engine lubrication may dissipate/disperse. Camshaft scoring or seizure may occur at initial start up
unless the procedure below is followed.
1. Refer to the MA section of the applicable Electronic Service Manual (ESM) to determine the specified volume of oil required to fill both the
crankcase and filter.
2. Set one (1) quart of oil aside and fill the crankcase with the remaining quantity (one quart should remain unused).
3. Prior to initial engine start up, pour the one (1) remaining quart of oil into the valve cover.
^ It is recommended to quickly squeeze the quart of oil out of the container to "flood" the camshafts and cam bearings.
4. Immediately start the engine while the upper end is "flooded" with oil.

Nissan-Datsun 370Z Technical 09-109 Date: 091007 Instruments - Clock Setting Procedure Classification: EL09-039

 Nissan-Datsun 370Z Technical  09-109 Date: 091007
Instruments - Clock Setting Procedure
Classification: EL09-039
Reference: NTB09-109
Date: October 7, 2009
370Z COUPE AND 370Z ROADSTER; TRIPLE METER CLOCK SETTING PROCEDURE
APPLIED VEHICLES:
2009-2010 370Z Coupe 2010 370Z Roadster
SERVICE INFORMATION
If the clock (located in the Triple Meter, above center in the instrument panel) needs to be set, use the procedure shown below.
  Page 225
NOTE:
Refer to Figure 1 for component location.
1. Turn the ignition on.
2. Press the Enter switch repeatedly until "Setting" shows in the upper right of the Vehicle Information Display.
3. Press the Next switch repeatedly until "Clock" is highlighted.
4. Press the Enter switch once.
5. Press the Next switch repeatedly until "Setting" is highlighted.
6. Press the Next switch repeatedly until the desired hour value is reached.
7. Press the Enter switch once.
8. Press the Next switch repeatedly until the desired minute value is reached.
9. Press the Enter switch once.
10. Press the Next switch repeatedly until "Back" is highlighted.
11. Press the Enter switch repeatedly until out of the setting mode.

Nissan-Datsun 370Z Technical 00-052C Date: 040416 Engine Controls - ECM Replacement Procedures Classification: EC00-007C

 Nissan-Datsun 370Z Technical  00-052C Date: 040416
Engine Controls - ECM Replacement Procedures
Classification:
EC00-007C
Reference:
NTB00-052C
Date:
April 16, 2004
ECM REPLACEMENT PROCEDURES
ATTENTION:
THIS BULLETIN HAS BEEN REVISED.
^ The Service Procedures for replacing an ECM on an Applied vehicle were revised.
^ Please use this bulletin NTB00-052c for complete information.
^ Discard all previously distributed copies of NTB00-052.
  Page 216
APPLIED VEHICLE(S):
All 2000 and later
1999 Frontier (D22)
1999 Quest (V41)
1999 Pathfinder (R50) from VIN JN8AR07**XW350101
IF YOU CONFIRM:
The Electronic Control Module (ECM) needs to be replaced on a 2000 MY and later vehicle, or an Applied 1999 MY vehicle (see above).
ACTIONS:
^ Re-register all customer keys if the vehicle has ECM based NATS (see step 1).
^ Check ASIST for any new updates for the new ECM you're installing (see steps 2 - 4).
^ Perform the "ACCELERATOR PEDAL & THROTTLE VALVE CLOSED POSITION LEARNING" procedure (see step 5).
^ After installing the new ECM, perform the "IDLE AIR VOL LEARNING" procedure (when applicable) using CONSULT-II. See step 6.
^ For 2005 and later vehicles, enter the vehicle VIN into the new ECM (see step 7).
CAUTION:
Failure to perform all the work steps in the specified order can cause poor engine running, MIL 'ON', or vehicle emission test rejection.
IMPORTANT:
The purpose of "ACTIONS" (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire
Service Procedure as it contains information that is essential to successfully completing this repair.
  Page 217
CLAIMS INFORMATION
Disclaimer
Service Procedure
Check NATS On The Vehicle
1. Check to see if the vehicle you're working on has "ECM based" NATS V2.0 or V5.0.
  Page 218
a. If the vehicle has ECM based NATS V2.0 or V5.0, it will NOT start after you install a service replacement ECM. So you'll have to
re-register all ignition keys, including spare keys with CONSULT-II and the purple NATS card. After you do this, proceed with step 2.
^ If you do not know how to re-register the keys, refer to the ESM for the NATS key re-registration procedure.
b. If the vehicle has "BCM based" NATS (instead of ECM based NATS V2.0 or V5.0), you do NOT have to re-register the ignition or
spare keys. Proceed with step 2.
Check For ECM Data Updates in ASIST
2. In ASIST, select [CONSULT Utilities] >>> [ECM/TCM Data]. Then choose Model and Model Year (see Figure 1).
3. Look for ECM Data Updates (listed by ECM P/Ns and vehicle configuration) in the top, center display panel of the ASIST screen (see Figure
1).
a. If there is not updates listed for your vehicle configuration, you do NOT have to reprogram the service replacement ECM. Proceed with
step 5.
b. If there is updates listed for your vehicle configuration, see if they apply to the service replacement ECM you're going to install. Do this
by performing step 4.
4. Select the "configuration" on the screen for the vehicle you're working on. Then confirm that your ECM is listed in the "Replaces
23710-XXXXX, -XXXXX, etc" section in the lower, center "Details" panel of the ASIST screen (see Figure 1).
a. If your ECM is listed in the "Details" panel, you must reprogram the ECM with the latest data update. After you do this, proceed with
step 5.
CAUTION:
The 1999-2000 Frontier and 1999-2000 Pathfinder have a gray CONSULT connector AND a white GST connector. Do NOT attempt to
perform the ECM Reprogramming procedure with CONSULT-II connected to the gray CONSULT connector. See the appropriate ESM
for further details if necessary.
b. If your ECM is NOT listed in the "Details" panel, you do NOT have to reprogram the ECM. Proceed with step 5.
Accelerator Pedal & Throttle Valve Closed Position Learning
5. Perform the Accelerator Pedal & Throttle Valve Closed Position Learning as follows:
a. Make sure the accelerator pedal is fully released.
b. Turn the ignition switch "ON" for 2 seconds.
c. Turn the ignition switch "OFF" for 10 seconds.
d. Turn the ignition switch "ON" for 2 seconds, then
  Page 219
e. Turn the ignition switch "OFF" again for 10 seconds (see Figure 2).
f. Proceed with step 6.
Perform Idle Air Volume Learning (IAVL)
NOTE:
Make sure all electrical loads are turned OFF, including A/C, defroster, radio, lights, etc. while performing the following procedures. Also,
make sure the engine cooling fans are NOT operating during the following procedures.
6. Perform the Idle Air Volume Learning procedure as follows:
a. Connect CONSULT-II to the vehicle.
b. Warm up engine and transmission to operating temperature.
c. In the [CONSULT WORK SUPPORT] mode, select [IDLE AIR VOL LEARN]. See Figure 3.
NOTE:
^ If IDLE AIR VOL LEARN is not shown as a SELECT WORK ITEM on CONSULT, the vehicle does not need the procedure.
^ In this case only, this bulletin is complete, no further action is needed.
  Page 220
d. Press [START] on the "IDLE AIR VOL LEARN" screen. See Figure 4.
e. Press [START] on the "WORK SUPPORT" screen to begin the Idle Air Volume Learning (IAVL) procedure. See Figure 5.
^ The IAVL procedure will take several minutes to complete.
^ CONSULT will display "Please Wait" in the center of the screen while the IAVL procedure is in process. See Figure 6.
  Page 221
^ CONSULT will display "CMPLT" in the top right corner of the screen when the IAVL procedure is finished. See Figure 7.
f. Once the IAVL procedure is finished, proceed with step 7.
For 2005 and Later MY Vehicles ONLY: Enter VIN Into New Service Replacement ECM
7. Enter the VIN into the new service replacement ECM as follows:
a. Select [ENGINE] on the "Select System" screen. See Figure 8.
b. Select [WORK SUPPORT] on the "Select Diag Mode" screen. See Figure 9.
  Page 222
C. Scroll down and select [VIN REGISTRATION] on the "Select Work Item" screen. See Figure 10.
d. Press [START] on the "VIN Registration" screen. See Figure 11.
e. Select [INPUT] on the "VIN Registration" screen. See Figure 12.
  Page 223
f. Enter the entire VIN using the keyboard. See Figure 13.
^ Use [CHNG] to switch between the letters and numbers keyboard screens.
g. Once the entire VIN is entered, select [ENTER] on the "Keyboard" screen. See Figure 14.
h. Select [INPUT] on the "VIN Registration" screen and enter the entire VIN again. See Figure 15.
^ You MUST enter the VIN a second time for confirmation purposes.
  Page 224
i. Once the entire VIN is entered (a second time), select [ENTER] on the "Keyboard" screen. See Figure 16.
j. Select [START] on the "VIN Registration" screen to complete the VIN registration process. See Figure 17.
k. Turn the ignition switch OFF and wait at least 10 seconds.

Nissan-Datsun 370Z Technical 10-145 Date: 101215 ABS/TCS - CAN Diagnostic Information Classification: BR10-011

Nissan-Datsun 370Z Technical  10-145 Date: 101215
ABS/TCS - CAN Diagnostic Information
Classification: BR10-011
Reference: NTB10-145
Date: December 15, 2010
ABS / VDC CAN DIAGNOSIS INFORMATION
APPLIED VEHICLES: All 2005-2011 Nissan vehicles with ABS and/or VDC
SERVICE INFORMATION
When diagnosing a vehicle with an ABS or VDC / SLIP warning light on with DTCs stored in the ABS / VDC actuator control unit, perform DTC
diagnosis first.
^ Do not replace the ABS / VDC actuator control unit without being supported by the DTC diagnosis.
^ Do not erase DTCs before performing DTC diagnosis.
^ Always fully diagnose before performing any repairs.
When DTC U1000 (CAN COMM CIRCUIT) is the only DTC stored in the ABS / VDC actuator control unit, use the REPAIR FLOW CHART
below. This will assist in proper diagnosis results and repairs in addition to using diagnostic information in the Electronic Service Manual (ESM).
^ If DTC U1000 is found stored in other systems, refer to NIB10-066 and the applicable ESM.
^ If other DTCs are found stored in ABS / VDC along with U1000, follow the diagnosis steps for those DTCs in the applicable ESM.
CLAIMS INFORMATION
Refer to the current Nissan Warranty Flat Rate Manual and use the appropriate claims coding for repairs performed.
  Page 214
  Page 215
Repair Flow Chart

Nissan-Datsun 370Z Technical 10-146 Date: 101217 Body - Convertible Top Frayed Near Door Windows Classification: BT10-041

 Nissan-Datsun 370Z Technical  10-146 Date: 101217
Body - Convertible Top Frayed Near Door Windows
Classification: BT10-041
Reference: NTB10-146
Date: December 17, 2010
2010 - 2011 370Z ROADSTER
DOOR WINDOWS CONTACTING SOFT TOP
APPLIED VEHICLES: 2010-2011 370Z (Z34)
IF YOU CONFIRM:
  Page 210
The soft top fabric is frayed (damaged) near a door window (left or right side) in the location shown in Figure 1.
and/or
The window is making contact with the soft top fabric when the door is opened or closed (see Figure 1 and Figure 1A),
ACTIONS:
Refer to the service procedure below.
PARTS INFORMATION
  Page 211
CLAIMS INFORMATION
SERVICE PROCEDURE
1. If the soft top fabric is damaged:
a. Replace the soft top fabric (cover).
^ Refer to the service manual as needed for soft top cover replacement.
^ Make sure to replace only the soft top cover and not the entire convertible top assembly.
b. After the soft top cover replacement, check door window to soft top clearance.
^ Open and close both front doors a few times.
^ Make sure the door window does not rub (contact) the soft top fabric.
^ If needed adjust the window.
If a door window rubs (contacts) the soft top fabric when opening and closing the door, adjust the window down and forward just enough to
prevent the window from contacting the fabric.
See Window Adjustment shown below.
2. If the soft top fabric is not damaged adjust the window - see Window Adjustment below.
3. Make sure there are no water or air leaks.
Window Adjustment
IMPORTANT:
Follow all cautions, warnings, and notes in the Electronic Service Manual (ESM) when working on or near a Supplemental Restraint System (SRS),
such as an air bag.
1. Write down all radio station pre-sets.
2. If equipped - write down / record the following customer settings for the ATC (Automatic Temperature Control) system (refer to the ESM as
needed):
^ Temperature Setting Trimmer
^ Foot Position Setting Trimmer
  Page 212
^ Inlet Port Memory Function
3. Turn the ignition switch OFF.
4. Disconnect both battery cables - negative cable first.
5. Wait for at least 3 minutes.
6. Remove the door panel (finisher).
^ Refer to the Service Manual, section INT / Interior, for door panel removal.
7. Reconnect the battery cables (positive cable first).
8. Operate the power window up or down as needed to access the bolts (A & B) shown in Figure 3.
9. Loosen the bolts (A & B) shown in Figure 3 just enough to allow window movement/adjustment.
NOTE:
The bolt holes are elongated. This will allow enough movement/adjustment to prevent the window from contacting the soft top fabric.
10. Adjust the window down and forward just enough to prevent the window from contacting the soft top.
11. Tighten the bolts.
12. After window adjustment, make sure:
^ It does not rub (contact) the soft top fabric.
^ There are no air leaks.
^ There are no water leaks.
NOTE:
You may need to adjust-and-check two or three times.
13. Disconnect both battery cables, negative cable first, and wait at least 3 minutes.
  Page 213
14. Reinstall the door panel.
^ Refer to the Service Manual, section INT / Interior, for door panel installation.
15. Reconnect the battery cables (positive cable first).
16. Reset the clock and the radio station presets.
17. Perform power window initialization.
^ Refer to section PWC in the Service Manual as needed.
^ Make sure initialization is performed with the soft top in the up/closed position.
18. If equipped - reset the customer settings for the ATC (Automatic Temperature Control) system (refer to the ESM as needed):
19. Turn the ignition from OFF to ON and confirm the Air Bag warning light goes OFF after about 7 seconds.

Nissan-Datsun 370Z Technical 11-029 Date: 110321 Page 206 Wheels/Tires - Tire Mounting Information Classification: WT11-003

Nissan-Datsun 370Z Technical  11-029 Date: 110321
  Page 206
Wheels/Tires - Tire Mounting Information
Classification: WT11-003
Reference: NTB11-029
Date: March 21, 2011
TIRE MOUNTING INFORMATION
APPLIED VEHICLES: All Nissan
SERVICE INFORMATION
^ When mounting tires to wheels, it is important that the tire bead is seated correctly.
^ A tire bead that is not seated correctly may cause a vehicle vibration.
^ High performance tires and tires with shorter sidewalls (low aspect tires) may require more care to make sure the tire bead is seated correctly.
^ Follow the Tire Mounting Tips in this bulletin.
Tire Mounting Tips:
NOTE:
These tips are not intended to be a complete instruction for mounting tires to wheels. Make sure to read and follow the instruction for your specific
tire service equipment
1. Clean the tire bead with an approved rubber cleaning fluid.
^ Rubber cleaning fluid is a locally sourced common product used in the tire service process.
2. Clean the wheel (flange and bead seat area) see Figure 2 Make sure to clean off all rust and corrosion.
  Page 207
3. Apply an approved tire lubricant to the tire and wheel in the areas shown in Figures 1 and 2.
^ Tire lubricant is a locally sourced common product used in the tire service process
Tire:
^ Apply lube to the inner bead only of both beads
^ Do not apply lube to the flange area (outer bead area)
NOTE:
Too much tire lubricant may allow the tire to slip on the rim while driving. If this occurs the tire may become un-balanced.
Wheel:
^ Apply lube to the Safety Humps and Bead Seating area.
^ Do not apply lube to the flange area
4. Before inflating the tire:
^ If there are "match-mount" marks on the tire and rim, align the marks.
^ Make sure the tire is evenly positioned on the lower safety humps.
5. WARNING: Do not exceed the tire manufactures recommended bead seating inflation pressure. Generally this is 40psi.
If the bead does not seat with the appropriate pressure:
a. Break down the tire/rim assembly.
b. Re-apply lubricant as shown in Figures 1 and 2.
  Page 208
c. Remount the tire.
6. After inflating the tires, inspect the bead area.
^ Make sure bead is seated uniformly (the same) around the entire circumference of the wheel.
NOTE:
Many tires have Aligning Rings that will help confirm the bead is uniformly seated.
If uniform; bead is seated correctly.
If not uniform
1. Break down the tire/rim assembly.
2. Re-apply lubricant as shown in Figures 1 and 2.
3. Remount the tire.
7. After the tire/wheel is balanced, apply an index mark to the tire at the location of the valve stem (see Figure 6).
^ This index mark will allow you to tell if the tire has slipped on the rim (see Figure 7).
Tire to Rim Slippage:
^ Too much tire lubricant may allow the tire to slip on the rim while driving. If this occurs, the tire may become un-balanced.
^ Overtime the tire lubricate will dry, eliminating the lubricant as a cause of tire slippage.
^ Some tire lubricants may require up to 24 hours to completely dry.
^ If slippage occurs, the tire/wheel will need to be re-balanced.
WORK - AID AVOID CUSTOMER RETURNS FOR VIBRATION
  Page 209
Print this page and keep it by your tire mounting equipment

Nissan-Datsun 370Z Technical 08-107A Date: 110504 Page 203 Intelligent Key(R) - System Inoperative

 Nissan-Datsun 370Z Technical  08-107A Date: 110504
  Page 203
Intelligent Key(R) - System Inoperative
Classification: EL08-028A
Reference: NTB08-107A
Date: May 4, 2011
INTELLIGENT KEY INOPERATIVE
This bulletin has been amended. The ACTIONS section has been revised. Please discard all previous versions.
APPLIED VEHICLES: All Nissan with Intelligent Key
IF YOU CONFIRM
The Intelligent Key is not functioning for any reason.
ACTIONS
1. Inspect the outside of the Intelligent Key for physical damage.
^ Look for cracks, dents, or other signs of physical damage.
NOTE:
Non-operation of the Intelligent Key due to physical damage is not covered under the vehicle warranty.
2. Open the Intelligent Key.
a) Remove the mechanical key from the Intelligent Key.
b) Place a piece of tape on the end of a small flathead screwdriver.
  Page 204
c) Insert the screwdriver into either of the slots shown in Figure 2.
d) Turn the screwdriver until the two cover pieces separate.
DO NOT PRY OPEN THE CASE FROM THE SIDE
3. Inspect the inside of the Intelligent Key for physical damage.
^ Look for components that are out of place or loose.
NOTE:
Non-operation of the Intelligent Key due to physical damage is not covered under the vehicle warranty.
  Page 205
4. Inspect the inside of the Intelligent Key for signs of water intrusion.
EXAMPLES OF WATER DAMAGE
NOTE:
Non-operation of the Intelligent Key due to water intrusion is not covered under the vehicle warranty.
5. Verify that the battery is inserted correctly.
^ The + side of the battery should not be showing when inserted correctly.
Make sure the + side of the battery is facing down.
6. Check the battery voltage.
^ Refer to the applicable Electronic Service Manual (ESM) for battery voltage inspection instructions. Depending on the vehicle, this information
can be found in one of the following locations:
> DLK section, "Check Intelligent Key Battery"
> BL section, "Intelligent Key Battery Inspection"
7. Refer to the ESM for additional Intelligent Key diagnostic and repair information.
^ Reference the current Nissan Warranty Flat Rate Manual for warranty information.

Nissan-Datsun 370Z Technical 11-054 Date: 110526 Wheels/Tires - Hunter GSP9700(R) Set Up Information Classification: WT11-006

Nissan-Datsun 370Z Technical  11-054 Date: 110526
Wheels/Tires - Hunter GSP9700(R) Set Up Information
Classification: WT11-006
Reference: NTB11-054
Date: May 26, 2011
NISSAN RECOMMENDED SETUP INFORMATION FOR HUNTER GSP9700
APPLIED VEHICLES: All Nissan
SERVICE INFORMATION
The most common cause of vehicle vibration at highway speeds is tire/wheel assembly non-uniformity. There are three primary contributors that
affect tire/wheel assembly uniformity:
^ Imbalance
^ Radial run-out
^ Tire Road Force Variation (RFV).
The Hunter GSP9700 has the capability to measure tire Road Force Variation (RFV). When measuring RFV it is important to look at both the RH1
and RH2 values.
Use the instructions below to set your Hunter GSP9700 to the Nissan recommended setting for optimum performance with Nissan wheel/tire
assemblies:
INSTRUCTIONS FOR ENTERING NISSAN RECOMMENDED SETTINGS INTO THE HUNTER GSP9700
  Page 194
Information
  Page 195
Enter Setup
  Page 196
Enable SmartWeight Only Balance Mode and ChangeWeightSaver Residual Goal
  Page 197
Enable Prompted Centering Checks
  Page 198
Set Road Force to Display Kilograms
  Page 199
Disable QuickMatch Setting
  Page 200
Set Weight Units to Display Grams
  Page 201
  Page 202
Set Runout & RoadForce Limits and Limits Multiplier for LT Tires and P/SUV Tires
Verify Settings