Friday, March 2, 2018

Nissan Armada Technical Service Bulletin # 08-097F Date: 111121

****************************
****************************

Nissan Armada Technical Service Bulletin # 08-097F Date: 111121
Steering/Suspension - Pull Or Drift Diagnostic Info
Nissan Armada 2wd v8 5.6L Parts Service 121
Classification: ST08-001F
Reference: NTB08-097F
Date: November 21, 2011
DIAGNOSIS OF VEHICLE PULL (DRIFT) AND STEERING WHEEL OFF CENTER
The General Procedures linked if you are using a internet copy of this bulletin has been amended. Please discard previous versions of these General
Procedures.
APPLIED VEHICLES: All Nissan - except GT-R
SERVICE INFORMATION
If a customers reports their "vehicle pulls" or the "steering wheel" is off-center, use the Diagnostic Flow Chart above and the other information in
this bulletin to diagnose and correct the issue
Road Test
Determine if the vehicle has a pull or steering wheel off-center issue that requires repair.
IMPORTANT:
^ If the vehicle has any tire issues, such as:
> Tires that are different sizes (except when specified from the factory)
> Significant difference in the amount of wear between any of the tires
> Any other tire irregularity or damage to any tire
Replace the tire(s) or use known good tires from another vehicle for all road tests and diagnostics in this bulletin.
^ Make sure tire pressure is set to the correct specification.
1. Install the following measuring tools on the vehicle:
^ Steering Wheel Offset Gauge
^ Road Crown Gauge
Nissan Armada 2wd v8 5.6L Parts Service 122
Nissan Armada 2wd v8 5.6L Parts Service 123
NOTE:
Refer above for a description of these tools and an explanation of their use.
2. Obtain a watch with a second hand (preferably a stopwatch) to use during the road test.
3. Take the vehicle for a road test and confirm the customers concern.
^ Select a flat road where the vehicle can be driven in a straight line at a preferred speed of 60 mph.
^ During the road test make sure the vehicle is pointing straight. Don't worry about steering wheel position during the road test.
NOTE:
^ If you adjusted the tire pressure or changed the tires before the road test, the issue may have been resolved.
^ If there are cross winds strong enough to affect the vehicle's straight line movement, then diagnosis cannot be performed.
4. Determine the vehicles issue - refer to the definitions of "Pull" and "Steering Wheel Off-center".
5. When the road test is completed, remove the Road Crown Gauge, leave the Steering Wheel Off-Set Gauge in place until the Service Procedure is
complete.
Nissan Armada 2wd v8 5.6L Parts Service 124
6. Refer to the Flow Chart for the next step.
Other Service Information
Customers may report that their vehicle's steering wheel is "off-center" because the steering wheel spokes are tilted to the left or right when the
vehicle continues straight ahead on a straight flat road (see example in Figure 1).
If a vehicle's steering wheel spokes are slightly off center while driving straight, it may be the normal result of road crown. Most roads in the United
States are built with a "crown" to help rain water drain from the road surface. The slope of the road crown varies from place to place.
Vehicles have a natural tendency to drift to the low side of the crown. The greater the slope of the crown, the faster the vehicle will drift in that
direction.
Tires and vehicles are designed to counteract the effect of typical road crown, but may not fully counteract the effect of a highly crowned road.
Some freeways slope to both the left and right from the center. When driving on a freeway that slopes in both directions, a vehicle may exhibit a
small amount of drift to the left when driving in the left lane and a small amount of drift to the right when driving in the right lane.
This bulletin does not address road crown issues because they are not vehicle related, although the customer may incorrectly perceive them to be.
Description/Definition of Steering Wheel "Off-center" Condition
The steering wheel spokes are tilted to the left or right more than allowable (see example in Figure 2) when driving straight ahead on a straight flat
road.
Allowable specification for steering wheel off-center
^ All Nissan (except NV1500, 2500, and 3500): 2 mm or less.
^ NV1500, 2500, and 3500: 4 mm or less.
When driving straight on a highly crowned road, the steering wheel may be turned (off-center) to counteract the affect of the road crown. When road
testing for an off-center condition, the vehicle should be driven on a straight flat road.
Nissan Armada 2wd v8 5.6L Parts Service 125
Although the vehicle does not pull in either direction, the customer may perceive that the vehicle pulls because it will respond if he or she tries to
bring the steering wheel back to center. This condition can occur if the tie rod length is uneven (not adjusted correctly) from side to side.
Description/Definition of a Vehicle "Pull" Condition
The vehicle consistently drifts to one side while driving at a constant speed on a straight, flat road.
^ A vehicle is said to "pull" if it completes a lane change in less than 7 seconds (with no steering correction from the driver) when driving at 60
MPH on a road with less than 2 degrees of road crown slope. All four wheels must pass into the other lane during this time (7 seconds).

Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) A L L Diagnostic Trouble Codes ( DTC ): B Code Charts Page 25

****************************
****************************

Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) A L L Diagnostic Trouble Codes ( DTC ): B Code Charts  Page 25
Replace the related harness.
- END
B1054
B1049 - B1052, B1054 - B1057 DRIVER AIRBAG MODULE
Description
DTC B1049 - B1052, B1054 - B1057 DRIVER AIRBAG MODULE
The driver air bag module is dual stage and wired to the air bag diagnosis sensor unit through the spiral cable.
The air bag diagnosis sensor unit will monitor for opens and shorts in detected lines to the driver air bag module including the spiral cable.
PART LOCATION
See: Restraints and Safety Systems/Air Bag Systems/Locations.
DTC Logic
DTC DETECTION LOGIC
With CONSULT-III
Without CONSULT-III
DTC CONFIRMATION PROCEDURE (With CONSULT-III)
1.INSPECTION START
Turn ignition switch ON.
- GO TO 2.
2.CHECK SELF-DIAG RESULT
Check for the DTC on CONSULT-III.
Is the DTC detected?
YES - See: B1049.
NO - Inspection End.
DTC CONFIRMATION PROCEDURE (Without CONSULT-III)

Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) A L L Diagnostic Trouble Codes ( DTC ): B Code Charts Page 24

****************************
****************************

Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) A L L Diagnostic Trouble Codes ( DTC ): B Code Charts  Page 24
Without CONSULT-III
DTC CONFIRMATION PROCEDURE (With CONSULT-III)
1.INSPECTION START
Turn ignition switch ON.
- GO TO 2.
2.CHECK SELF-DIAG RESULT
Check for the DTC on CONSULT-III.
Is the DTC detected?
YES - See: B1049.
NO - Inspection End.
DTC CONFIRMATION PROCEDURE (Without CONSULT-III)
NOTE:
SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.IGNITION SWITCH
Turn ignition switch ON.
- GO TO 2
2.IGNITION SWITCH
After air bag warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second.
- GO TO 3
3.WAIT TIME
Wait more than 3 seconds.
- GO TO 4
4.REPEAT STEPS
Repeat steps 1 to 3 twice.
- GO TO 5.
5.IGNITION SWITCH
Turn ignition switch ON.
- GO TO 6.
6.DIAGNOSTIC MODE
SRS system is now in diagnostic mode and AIR BAG warning lamp flashes. See: Restraints and Safety Systems/Air Bag Systems/Testing and
Inspection/Scan Tool Testing and Procedures/Diagnosis Sensor Unit/Trouble Diagnosis Without CONSULT-III.
- END
Diagnosis Procedure (Component Diagnosis)
Recheck SRS after each replacement.
1.HARNESS CONNECTOR
Is there any visible damage to the connector?
YES or NO
YES - Replace the harness.
NO - GO TO 2
2.WIRING HARNESS
Is there any visible damage to the harness?
YES or NO
YES - Replace the harness.
NO - GO TO 3
3.DRIVER AIR BAG MODULE
Replace the driver air bag module. See: Restraints and Safety Systems/Air Bag Systems/Air Bag/Service and Repair/Driver Air Bag Module.
- GO TO 4
4.SPIRAL CABLE
Replace the spiral cable. See: Restraints and Safety Systems/Air Bag Systems/Clockspring Assembly / Spiral Cable/Service and Repair.
- GO TO 5
5.AIR BAG DIAGNOSIS SENSOR UNIT
Replace the air bag diagnosis sensor unit. See: Relays and Modules/Relays and Modules - Restraints and Safety Systems/Air Bag Control
Module/Service and Repair.
- GO TO 6
6.RELATED HARNESS

Thursday, March 1, 2018

Nissan Armada Technical Service Bulletin # 09-140 Date: 091208

****************************
****************************

Nissan Armada Technical Service Bulletin # 09-140 Date: 091208
A/T - CVT Oil Leak Diagnosis Information
Classification: AT09-012
Reference: NTB09-140
Date: December 8, 2009
CVT OIL LEAK DIAGNOSIS USING FLORESCENT DYE
APPLIED TRANSMISSION: Continuously Variable Transmission (CVT)
SERVICE INFORMATION
If you have a CVT that appears to have oil seepage or a leak on the transmission, follow the steps below to assist in a correct diagnosis.
1. Thoroughly clean off the area of the suspected leak.
2. Install 1 fluid ounce of J-28431 Fluorescent Oil Dye* into the CVT.
3. Drive vehicle for a minimum of 30 minutes (to ensure proper diagnosis).
4. Inspect with lamp from J-43926 A/C Dye Kit*
If no fluorescent oil trace/leak is found, the stain is probably:
^ corrosion protection chemicals sprayed on the transmission
and/or
^ lubricants which are sometimes used to ease the assembly process.
NOTE:
Nissan Armada 2wd v8 5.6L Parts Service 265
These may cause dust to accumulate (gather) on the transmission and have the appearance of an oil leak. Neither of these requires corrective action.
If a fluorescent oil trace/leak is found:
^ Repair using standard warranty procedures.
*These tools were made Essential in 2001 (J-28431) and 1999 (J-43926). They are also available from Tech Mate.
NOTE:
The Fluorescent Oil Dye is also available from Tech Mate in a pack of six 1 ounce bottles. That pack is available as part number J-28431-6.

Nissan Armada Technical Service Bulletin # 09-088 Date: 090910

****************************
****************************.
Nissan Armada Technical Service Bulletin # 09-088 Date: 090910
Body - Power Liftgate Won't Open/Close/Is Noisy
Classification: EL09-023
Reference: NTB09-008
Date: September 10, 2009
2004 - 2010 ARMADA; POWER BACK DOOR WILL NOT OPEN/CLOSE AND MAKES NOISE
APPLIED VEHICLES: 2004 - 2010 Armada (TA60) with power back door.
IF YOU CONFIRM:
While operating the power back door (lift gate),
^ The power motor will not open or close the door,
and/or
^ There is a grinding and popping noise inside the rear trim panel.
ACTION:
1. Check for loose or missing bolt on the power back door motor assembly.
^ Replace if needed.
Nissan Armada 2wd v8 5.6L Parts Service 239
2. Check for bent or damaged power back door motor mounting brackets.
^ Replace if needed.
IMPORTANT:
The purpose of ACTIONS (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire Service
Procedure as it contains information that is essential to successfully completing this repair.
PARTS INFORMATION
CLAIMS INFORMATION
SERVICE PROCEDURE
Nissan Armada 2wd v8 5.6L Parts Service 240
1. Access the power back door motor assembly.
^ Remove left side finishers as needed.
^ Refer to the Service Manual as needed (section BL 2004 07, section DLK 2008 - 2010).
^ Bolt A shown in Figure 1 will need to be removed.
NOTE:
You may not need to completely remove the lower luggage finisher. Unclipping the top and pulling it back may give you enough access.
2. Check bolt "B" (see Figure1).
^ If bolt B is loose or missing, replace it with a new one.
^ New bolt is listed in the parts information.
^ Apply Permatex(R) Medium Strength Threadlocker BLUE (or equivalent) to the threads of the new bolt and torque bolt to:
5.7 N穖 (0.6 kg-m, 51 in-lb)
Nissan Armada 2wd v8 5.6L Parts Service 241
NOTE:
If bolt B is missing, make sure to find the missing bolt and remove it from the vehicle. The missing bolt, if left loose in the passenger compartment,
could cause a rattle.
3. Check both mounting brackets.
^ If mounting brackets are bent or damaged, replace with new brackets (see Figure 3).
^ New brackets are listed in the Parts Information.
^ Torque for back door motor mounting bolts is:
5.7 N穖 (0.6 kg-m, 51 in-lb)
NOTE:
Nissan Armada 2wd v8 5.6L Parts Service 242
^ Figure 3, is a close up view of the mounting brackets.
^ The brackets can be replaced without completely removing the motor assembly.
4. Reassemble all parts in reverse order.
^ Apply Permatex(R) Medium Strength Threadlocker BLUE (or equivalent) to the threads of bolt A and torque bolt to:
15.2 N穖 (1.6 kg-m, 11 ft-lb)
5. Make sure the power back door motor works correctly with no abnormal noise.
^ Cycle the power back door (open and close) 5 times.
NOTE:
Each bracket is held on with 2 screws.
^ Re-use screws and torque to:
5.7 N穖 (0.6 kg-m, 51 in-lb)

Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) A L L Diagnostic Trouble Codes ( DTC ): B Code Charts Page 121

****************************
****************************

Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) A L L Diagnostic Trouble Codes ( DTC ): B Code Charts  Page 121
Is the inspection result normal?
YES - Replace pedal adjusting motor assembly. See: Accessories and Optional Equipment/Pedal Positioning System/Pedal Positioning
Motor/Service and Repair.
NO - GO TO 5
5. CHECK INTERMITTENT INCIDENT
See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Intermittent Incident.
Is the inspection result normal?
YES - Replace automatic drive positioner control unit. See: Accessories and Optional Equipment/Memory Positioning Systems/Memory
Positioning Module/Service and Repair/Removal And Replacement.
NO - Repair or replace the malfunctioning part.
B2120
B2120 ADJ PEDAL SENSOR
Description
- The pedal adjusting sensor is installed in the pedal adjusting motor assembly.
- The resistance of pedal adjusting sensor is changed according to the forward/backward position of pedal adjusting motor assembly.
- The terminal voltage of automatic drive positioner control unit will be changed according to a change of pedal adjusting sensor resistance.
Automatic drive positioner control unit calculates the pedal assembly position from the voltage.
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1. STEP 1
Turn ignition switch ON.
- GO TO 2
2. STEP 2
Check "Self diagnostic result" with CONSULT-III.
Is the DTC is detected?
YES - Perform diagnosis procedure. See: B2120.
NO - Inspection End.
Diagnosis Procedure
Regarding Wiring Diagram information, See: Accessories and Optional Equipment/Memory Positioning Systems/Diagrams/Electrical
Diagrams/Automatic Drive Positioner Control Unit.
1. CHECK PEDAL ADJUSTING SENSOR SIGNAL
1. Turn ignition switch ON.
2. Select "PEDAL SEN" in "Data monitor" mode with CONSULT-III.
3. Check the pedal adjusting sensor signal under the following condition.
Is the value normal?
YES - Pedal adjusting circuit is OK.

Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) A L L Diagnostic Trouble Codes ( DTC ): B Code Charts Page 110

****************************
****************************

Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) A L L Diagnostic Trouble Codes ( DTC ): B Code Charts  Page 110
6.DIAGNOSTIC MODE
SRS system is now in diagnostic mode and AIR BAG warning lamp flashes. See: Restraints and Safety Systems/Air Bag Systems/Testing and
Inspection/Scan Tool Testing and Procedures/Diagnosis Sensor Unit/Trouble Diagnosis Without CONSULT-III.
- END
Diagnosis Procedure (Component Diagnosis)
Recheck SRS after each replacement.
1.HARNESS CONNECTOR
Is there any visible damage to the connector?
YES or NO
YES - Replace the harness.
NO - GO TO 2
2.WIRING HARNESS
Is there any visible damage to the harness?
YES or NO
YES - Replace the harness.
NO - GO TO 3
3.LH SIDE CURTAIN AIR BAG MODULE
Replace the LH side curtain air bag module. See: Restraints and Safety Systems/Air Bag Systems/Side Air Bag/Service and Repair/Side Curtain
Air Bag Module.
- GO TO 4
4.AIR BAG DIAGNOSIS SENSOR UNIT
Replace the air bag diagnosis sensor unit. See: Relays and Modules/Relays and Modules - Restraints and Safety Systems/Air Bag Control
Module/Service and Repair.
- GO TO 5
5.RELATED HARNESS
Replace the related harness.
- END
B1201
B1198 - B1201 SIDE CURTAIN AIR BAG MODULE LH (FRONT)
Description
DTC B1198 - B1201 LH SIDE CURTAIN AIR BAG MODULE (FRONT)
The LH side curtain air bag module (front) is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit will monitor for opens
and shorts in detected lines to the LH side curtain air bag module (front).
PART LOCATION
See: Restraints and Safety Systems/Air Bag Systems/Locations.
DTC Logic
DTC DETECTION LOGIC
With CONSULT-III
Without CONSULT-III

Nissan Armada Technical Service Bulletin # 05-097E Date: 120405

****************************
****************************

Nissan Armada Technical Service Bulletin # 05-097E Date: 120405
Steering/Suspension - Front End Alignment Cam Bolts
Classification: FA05-002E
Reference: NTB05-097E
Date: April 5, 2012
2005-2012 TITAN AND ARMADA;
CAM BOLTS FOR FRONT WHEEL ALIGNMENT
Nissan Armada 2wd v8 5.6L Parts Service 113
The Applied Vehicles have been updated/amended. Please discard previous versions of this bulletin.
APPLIED VEHICLES2: 005 - 2012 Titan (A60)
2005 - 2012 Armada (TA60)
APPLIED VINS: 2005 Titan built after 1N6AA0(***)5N 566358
2005 Armada built after 5N1AA08(**)5N 733885
2006 - 2012 vehicles: All VINs
APPLIED DATE: Vehicles built after June 2, 2005
IF YOU CONFIRM
An Applied Vehicle needs to have the front wheel alignment adjusted,
NOTE:
Applied Vehicles listed above come from the factory with non-adjustable bolts (Not Cam Bolts) for the lower link (lower control arm) mounting.
ACTIONS
1. Remove the original lower link mounting bolts, washers, and nuts - 2 per side.
^ Refer to section FSU in the Electronic Service Manual (ESM) for lower link mounting bolt locations.
2. Install new bolts (cam bolts), cam washers and new nuts.
^ New parts are listed in the Parts Information section of this bulletin.
NOTE:
Cam bolts are used to adjust caster and camber.
3. Perform front wheel alignment per the ESM.
PARTS INFORMATION
CLAIMS INFORMATION

C1132 C1130, C1131, C1132, C1133, C1136 ENGINE SIGNAL

****************************
****************************

C1132
C1130, C1131, C1132, C1133, C1136 ENGINE SIGNAL
Description
ABS actuator and electric unit (control unit) and ECM exchange the engine signal with CAN communication line.
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAGNOSIS RESULTS
Check the self-diagnosis results.
Is above displayed on the self-diagnosis display?
YES - Proceed to diagnosis procedure. See: C1130.
NO - Inspection End
Diagnosis Procedure
1.CHECK ENGINE SYSTEM
1. Perform ECM self-diagnosis. Repair or replace items indicated, then perform ECM self-diagnosis again. See: Powertrain
Management/Computers and Control Systems/Testing and Inspection/Scan Tool Testing and Procedures/CONSULT-III Function (Engine).
2. Perform ABS actuator and electric unit (control unit) self-diagnosis. See: Brakes and Traction Control/Antilock Brakes / Traction Control
Systems/Testing and Inspection/Scan Tool Testing and Procedures.
Is any item indicated on the self-diagnosis display?
YES - Repair or replace the affected part.
NO - Inspection End
Special Repair Requirement
1.ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
Always perform neutral position adjustment for the steering angle sensor when replacing the ABS actuator and electric unit (control unit). See:
Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Steering Angle Sensor/Testing and Inspection/Description.
- GO TO 2
2.CALIBRATION OF DECEL G SENSOR
Always perform calibration of decel G sensor when replacing the ABS actuator and electric unit (control unit). See: Brakes and Traction
Control/Antilock Brakes / Traction Control Systems/Yaw Rate Sensor/Testing and Inspection/Description.
- END

Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) A L L Diagnostic Trouble Codes ( DTC ): B Code Charts Page 66

****************************
****************************

Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) A L L Diagnostic Trouble Codes ( DTC ): B Code Charts  Page 66
NO - GO TO 3
3.FRONT RH SIDE AIR BAG MODULE
Replace the front RH seat back assembly. See: Body and Frame/Seats/Service and Repair/Front Seat/Removal and Installation.
- GO TO 4
4.AIR BAG DIAGNOSIS SENSOR UNIT
Replace the air bag diagnosis sensor unit. See: Relays and Modules/Relays and Modules - Restraints and Safety Systems/Air Bag Control
Module/Service and Repair.
- GO TO 5
5.RELATED HARNESS
Replace the related harness.
- END
B1130
B1129 - B1132 SIDE AIRBAG MODULE RH
Description
DTC B1129 - B1132 FRONT RH SIDE AIR BAG MODULE
The front RH side air bag module is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit will monitor for opens and shorts
in detected lines to the front RH side air bag module.
PART LOCATION
See: Restraints and Safety Systems/Air Bag Systems/Locations.
DTC Logic
DTC DETECTION LOGIC
With CONSULT-III
Without CONSULT-III
DTC CONFIRMATION PROCEDURE (With CONSULT-III)
1.INSPECTION START
Turn ignition switch ON.
- GO TO 2.
2.CHECK SELF-DIAG RESULT
Check for the DTC on CONSULT-III.
Is the DTC detected?
YES - See: B1129.
NO - Inspection End.
DTC CONFIRMATION PROCEDURE (Without CONSULT-III)
NOTE:
SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.IGNITION SWITCH
Turn ignition switch ON.

Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) A L L Diagnostic Trouble Codes ( DTC ): B Code Charts Page 23

****************************
****************************

Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) A L L Diagnostic Trouble Codes ( DTC ): B Code Charts  Page 23
Diagnosis Procedure (Component Diagnosis)
Recheck SRS after each replacement.
1.HARNESS CONNECTOR
Is there any visible damage to the connector?
YES or NO
YES - Replace the harness.
NO - GO TO 2
2.WIRING HARNESS
Is there any visible damage to the harness?
YES or NO
YES - Replace the harness.
NO - GO TO 3
3.DRIVER AIR BAG MODULE
Replace the driver air bag module. See: Restraints and Safety Systems/Air Bag Systems/Air Bag/Service and Repair/Driver Air Bag Module.
- GO TO 4
4.SPIRAL CABLE
Replace the spiral cable. See: Restraints and Safety Systems/Air Bag Systems/Clockspring Assembly / Spiral Cable/Service and Repair.
- GO TO 5
5.AIR BAG DIAGNOSIS SENSOR UNIT
Replace the air bag diagnosis sensor unit. See: Relays and Modules/Relays and Modules - Restraints and Safety Systems/Air Bag Control
Module/Service and Repair.
- GO TO 6
6.RELATED HARNESS
Replace the related harness.
- END
B1052
B1049 - B1052, B1054 - B1057 DRIVER AIRBAG MODULE
Description
DTC B1049 - B1052, B1054 - B1057 DRIVER AIRBAG MODULE
The driver air bag module is dual stage and wired to the air bag diagnosis sensor unit through the spiral cable.
The air bag diagnosis sensor unit will monitor for opens and shorts in detected lines to the driver air bag module including the spiral cable.
PART LOCATION
See: Restraints and Safety Systems/Air Bag Systems/Locations.
DTC Logic
DTC DETECTION LOGIC
With CONSULT-III